Quality Inspection for 771 PPR Male Thread Coupling Export to Iraq
We are committed to providing easy,time-saving and money-saving one-stop purchasing service of consumer for Quality Inspection for 771 PPR Male Thread Coupling Export to Iraq, We invites you and your enterprise to thrive together with us and share a bright future in global market.
Who We Are
Ningbo Aimei Meter Manufacture Co., Ltd. is located in Fenghua City(south Ningbo), which is two hours away from Shanghai by train. The company was established in 1987 as a leading manufacturer and exporter in the water meter field for more than 25years. Since its foundation ,the company has grown up quickly with a construction area of 20,000 square meters and 200 staff, including 20 high-class or primary technicians . Now its annual production capacity is 3 millions units.
AIMEI Meter holds advanced equipment and high technology to make full range of quality water meters from DN15(1/2”) to DN600(24”). The company adopts ISO4064 & OIML-R49 international standard, MID 2004/22/EC European standard and NSF-61 standard in producing water meters. Its product range covers Single jet, Multi jet, Volumetric piston type, Woltman type and Smart water meters. At present, Aimei water meters are already exported to over 60 different countries worldwide.
AIMEI continues to improve Quality System Management and renews ISO 9001:2008 Certificate and ISO14001:2004 certificate.
All the water meters are manufactured in compliance with ISO 4064 international standard which ensure the legitimacy and quality of product stability.
How to make silver ring: We will make pairing from one ring with just the tools available at home center without using engraving tool (what you need is below ↓).
* It is a video from Japan.
I write commentary using translation software.
I am sorry if there is a mistranslation.
I want to handmade a surprise gift, but …
But, it is only for one time to arrange the engraving tools
Neither psycho nor budgetary is impossible! It is a little hard!
Is not it that there are many people?
Therefore, without using the engraving tool
With 100 tools and tools available at home centers or familiar items that can be substituted
I tried to think of a way to make pairing (two) from one ring.
* Even if someone accustomed to ring making does it, it feels like “This is a terrible work!”
Completed ring =
No. 13: 2.3 mm width, 2.3 mm thickness,
No. 17 = 1.8 mm wide 2.2 mm thick.
Although the inner side of the ring is not a true circle, since the finger itself is not a perfect circle, there is no problem at all. If it is in a large deformation state, it will be struck vertically to correct it to nearly a circle.
* Attention point of this video:
Actual work time and work time in the movie are different as we cut and connect the videos in various scenes.
The melting work in the burner was done as much as possible with “no editing”, but there are scenes that cut a little.
Tool used this time:
Stainless steel pipe (instead of core bar / diameter 12 mm, 15 mm etc. / diameter changes from ring sizing)
Table leg rubber 2 (inside diameter = about 28 mm),
File: round, flat, diamond (100 equal),
Drill: 2 mm diameter (ring thickness),
Paper file (240, 400, 800, 1500, 2000),
Handy gas burner (flame temperature 1000 ° C),
Heat resistant block (for many holes, for soldering),
Tweezers (first bent type is recommended),
↑ If you sum up this amount, it will be a good amount of money.
I got a hint from my original technique I’ve done in various works so far
Casting (= putting a toothpick: how to make Nasu no Fujiro),
Sherbet melting (how to make ingenious silver ring),
In ring size adjustment, over 30 size oversized ring technique is utilized.
Creative silver ring construction
I used a “circular ruler” to figure out the size of the ring
Because the No. 1 will easily differ easily depending on the thickness of the ring
It is a guide only.
Basically, make the ring prototype small
It is the idea of expanding by tapping and adjusting the size.
When the length of the diameter of the circle is “1 mm” different, the size of the ring is “No. 3″ different.
It’s rough, but it’s a circle ruler
“14 mm = No. 6″,
“15 mm = 9″,
“16 mm = 12″,
“17 mm = 15″,
“18 mm = 18″,
“19 mm = 21″,
“20 mm = 24″,
“21 mm = 27″,
“22 mm = 30″,
This is almost the same as the outer diameter of the finger (About).
This intermediate size is “Make it small and hit it and spread it out to fit the size.”
As a precaution, when the ring thickness (= diameter of the drill) is 2 mm
It is necessary to add “2 mm X 2 = 4 mm”.
For example, in the case of this ring making, using a circle ruler of “19 mm, 21 mm”
We have completed No. 13 and No. 17.
The number 1 will easily differ depending on the hit. Also, when finishing the inside of the ring it will spread about 0.5.
Creative silver studio Otanko Nasu!